.jpg)
⚙️ Iveco Daily 35C – 35S Front Brake Pad Wear Sensors – Electronic detection of brake pad wear and dashboard alert
🔧 What is this part for?
The front wear sensors are small electronic sensors mounted on the front brake pads. When the pads are too worn, the brake rotor rubs against the sensor until it breaks, which causes a warning light to come on in the instrument panel. This alerts the driver in time to replace the pads before they lose their effectiveness or cause serious damage to the brake rotors. On the Iveco Daily 35C and 35S, the front axle handles most of the braking load, especially when the vehicle is loaded and in city traffic. Therefore, monitoring the wear on these pads is most important. A defective or missing indicator eliminates this warning, and the pads can then wear down to the metal without warning.
This genuine Iveco part is sold new as a set of two indicators—one for the left front wheel and one for the right front wheel. It is an exact replacement for the original front brake pad wear indicators on the Iveco Daily 35C and 35S models from model years 2009, 2012, 2016, 2019, 2022, and 2024. It connects directly to the existing wiring harness without requiring any modifications. It is part of the Iveco Daily braking system, monitoring front brake wear.
✅ Technical
Specifications
Compatibility: Iveco Daily 35C and 35S – MY2009, MY2012, MY2016, MY2019, MY2022, MY2024
Type: Brake
pad wear indicator (electrical sensor)
Position: Front axle, left and right
Function: Detects when brake pads reach the wear limit and illuminates the warning light on the dashboard
Installation: Mounts directly to the front
brake pads
Packaging: Set of 2 sensors (1 per side)
Condition: New – Genuine Iveco
part
OEM Part Number: Iveco 42567353
Part Number: 3794940904050
✅ Why replace this part?
✅ A severed or torn wear indicator will no longer trigger an alert: the front brake pads can wear down to the metal backing plate and scratch—or even destroy—the brake rotors.
✅ A wear indicator that has already been triggered keeps the warning light on continuously. The warning then loses its value and may mask a genuine braking malfunction.
✅ A set of new, genuine wear sensors restores reliable detection on both sides of the front axle and allows you to replace the front brake pads before they lose effectiveness.
✅ Signs of wear / failure / replacement
When the brake pad wear warning light on the dashboard comes on, it generally indicates that the pad has reached the sensor and that the pads have reached their wear limit. Once the light goes out, it has served its purpose and the brake pads should be replaced. A light that remains on after installing new brake pads almost always indicates a reused sensor, a broken wire, or a loose connector. A flashing light is more likely caused by a chafed wire or a connector corroded by water and salt spray. Conversely, if the light does not come on even though the pads are visibly worn, the indicator is disconnected or out of service and must be checked immediately.
✅ Installation
Tips
Always replace the wear indicators whenever you change the front brake pads, and always on both sides of the axle. Snap each indicator into its housing on the brake pad, then route the wire through its original guides and clips, keeping it away from the rotor, caliper, and steering components, taking into account the wheel’s steering angle. Check that the connectors are clean and securely locked in place. After installation, verify that the wear indicator light turns off when the ignition is on, then turn the steering wheel fully in both directions to ensure the wires are neither taut nor pinched. Installation by a qualified professional is recommended, as the braking system is a safety-critical component.
✅ Technical advice from RAXOR Parts
On the Iveco Daily 35C and 35S, the front wear indicators must be replaced at the same time as the Iveco Daily brake pads: a cut or reused indicator will no longer provide any warning for the next wear cycle. On the front end, the indicator wires are also subject to steering movements: improper cable routing is enough to cause premature disconnection and a false warning light. Take advantage of this service to check the condition and thickness of the front rotors, as well as the free movement of the Iveco Daily brake caliper. A seized caliper causes the pads to wear quickly and unevenly, which triggers the warning light too early.
✅ Why choose RAXOR Parts?
✅ Set of 2 genuine Iveco front wear indicators, OEM part number 42567353, compatible with Daily 35C and 35S models from MY2009 to MY2024; direct installation without modification.
✅ Front brake pads, rotors, and calipers available for a complete front brake overhaul in a single order.
✅ In stock and fast shipping to minimize downtime for your work vehicle.
Contact
📧 Contact us by email with any compatibility questions.
💬 Use the live chat for a quick response.
🚚 Order your Iveco Daily 35C–35S
front brake wear indicators now
Order your set of genuine front wear indicators today from RAXOR Parts and receive them quickly, ready to install on your Iveco Daily 35C or 35S.
